AMPLIFONE HV REV A201012-04, ALL PARTS LIST
Updated 09-October-2016
| Amplifone Circuit Ref |
Original Part |
QTY per board | Pic | Additional Info | Replaced with | Alternative | Alternative |
| C1, C2 | 470uF 50V Capacitor, Radial | 2 | 7.5mm between leads b/n centres | 470uF 100V Capacitor | 63V, 477KXM063MQV, 16mm x 25mm | 100V, 477KXM100M, 16mm x 40mm | |
| C3, C4 | 100uF 35V Capacitor, Radial (Use 220uF) | 2 | 5mm between leads b/n centres | 220uF 50V Capacitor | Element14.com.au | ||
| C5 | 4.7uF 50V Capacitor Axial or Radial | 1 | Element14.com.au | ||||
| C6 | 0.0047uF 100V Mylar Capacitor, Radial | 1 | Jaycar | Futurelec.com.au | P/No # C0047UM | ||
| C7, C9 | 0.01uF Ceramic 50V, Axial | 2 | Glass | Element14.com.au | C010UMC - 0.01uF 50V Multilayer Ceramic Capacitor | futurlec.com | |
| C8 | 0.033uF 600V Polyprop. | 1 | Mylar Jaycar | Element14.com.au 630V | Futurelec.com.au 400V | ||
| C10, C12, C13 | 0.1uF Ceramic 50V, Axial | 3 | Glass | Element14.com.au | C100UMC - 0.1uF 50V Multilayer Ceramic Capacitor | Futurlec.com | |
| C11 | 0.001uF Ceramic 1000V, Radial | 1 | Ceramic Disk | Element14.com.au | |||
| CR1 | 1N914 diode | 1 | Element14.com.au | 1N4148 | |||
| CR2 | Red LED | 1 | Anywhere | ||||
| CR3 | BYV26G | 1 | 0.4A, 1500 PIV Fast- Recovery Rectifier. | HY15F or NTE558 | Element 14: BY448-TR | Alt BY448TAP | |
| CR4 | Zener 6.8V 1N754A | 1 | X-ON (12W) $0.10ea / 10 | Element14.com.au | DIODE ZENER 6.8V 500MW (DO-35) | Markhinds.co.uk | |
| CR5, 6 | 1N4001 diode | 2 | Element14.com.au | ||||
| CR8 | MUR2100EG diode MUCH CHEAPER UF2008 | Optional | Optional part (RECENTLY EDITED) | Element14.com.au | Only needed if BU406 is used in Q3 ("D" missing) | ||
| Q1, Q5 | 2N3904 transistor | 2 | Element14.com.au | ||||
| Q2 | MPSU-07 | 1 | Bob Roberts | SK3199, CEN-07 | Markhinds.co.uk joesarcade.com | ||
| Q3 | BU406D | 1 | homepin.com | rockby.com.au | Mouser | ||
| Q4 | SCR MCR100-3 (osolete) Use X0202MA 1BA2 | 1 | Aliexpress Element14 | 0.8A 600V (TO-92) | BT169G | ||
| R5 | 1.2KΩ, 1/2W resistor | 1 | |||||
| R6 | 3.9KΩ, 1/2W resistor | 1 | |||||
| R7 | 2KΩ Trimpot | 1 | Element14.com.au | Bournes Trimmer sheet | |||
| R8, R25 | 1KΩ, 1/2W resistor | 1 | |||||
| R9 | 22KΩ, 1/2W resistor | 1 | |||||
| R10 | 4.7KΩ, 1/2W resistor | 1 | |||||
| R11, R12, R15 | 2.2KΩ, 1/2W resistor | 3 | |||||
| R13 | 39Ω, 1/2W resistor | 1 | |||||
| R17 | 20KΩ Trimpot | 1 | Link fixed to the right | Element14.com.au | Mouser 652-3386P-1-203LF. | Bournes Trimmer sheet | |
| R19 | 68KΩ, 1/2W resistor | 1 | If using the original Amplifone Focus Block | ||||
| R19 | 100KΩ, 1/2W resistor | If using the a WG6100 Focus Block | If 68KΩ is used the HV will not cut off at 25KV | ||||
| R20, R21 | 50Ω, 5W resistor | 2 | 50Ω 30W resistor $5.97 | 47Ω 30W resistor | 50Ω 30W resistor TO-220 | 47Ω 30W resistor TO-220 or Digikey | |
| VR1 | 7824 (+ve) Regulator | 1 | (No insulator) | Element14.com.au | ECG972 | ||
| VR2 | 7924 (-ve) Regulator | 1 | (Insulator) | Element14.com.au | ECG971 | ||
| U1 | NE555N timer IC | 1 | Element14.com.au | ||||
| FA1 | Focus Assy DIY | 1 | How to see post # 121 & 122 | Twisted Quarter | |||
| MK3306 | TO-220 insulator | 1 | For VR2 only (Neg Regulator) | Element14.com.au | |||
| Neck11 | Neck Connector 11 pin | 1 | |||||
| T2 | Flyback | 1 | Twisted Quarter | ||||
| R26 | Resistor in Neck Connector | 1 | On Focus pin # 1 (10K, 1W) | ||||
| R27 | Resistor in Neck Connector | 1 | On G1 pin # 5 (2.2K, 1W) | ||||
| R28 | Resistor in Neck Connector | 1 | On G2 pin # 6 (2.2K, 1W) | ||||
| P103 | 9 WAY CONNECTOR HOUSING | 1 | 538-50-84-1090 MOUSER | x-on.com.au | |||
| P102 | 3 WAY CONNECTOR HOUSING HV Harness side of DAG wire | 1 | 538-50-84-2030 MOUSER | x-on.com.au | |||
| J102 | 3 WAY MATING CONNECTOR DAG Wire Side | 1 | 538-50-84-1035 MOUSER | ||||
| P104 | 2 WAY Connector for Degauss | 1 | 538-50-84-2022 MOUSER | ||||
| P102 pins | PIN TERMINAL MALE (For 3 way) | 2 | 538-02-08-2004 MOUSER | 1629253 ELEMENT14 | x-on.com.au | ||
| P103 Pins | PIN TERMINAL FEMALE (For 9 way) | 8 | 538-02-08-1002 MOUSER | 1685109 ELEMENT14 | x-on.com.au | ||
| Heatsink | Heatsink Suit Q3 | 1 | Digi-Key US | x-on AU | |||
| Pin Arrow | Plastic arrow clip, 561-AC020 | 1 | Mouser | X-ON | Holds down Q2 to PCB | ||
| MC1 AIR | REPRO Air core choke | Optional | Amazing Arcading | ||||
| MC1 RECT | REPRO Rectangular Choke | Optional | Amazing Arcading | ||||
| MC1 TOR | REPRO Round Choke | Optional | Amazing Arcading | ||||
| T1 | REPRO Driver Transformer | 1 | Amazing Arcading | ||||
| HS-Glue | Heat Shrink Tube - Glue Lined Suit Focus block | 2 | Amazing Arcading | ||||
| PCB Bare | Part No DB-A201012-04 | 1 | Amazing Arcading | ||||
| NeckPCB | New Neck PCB | 1 | Amazing Arcading | ||||
| Conn12WayF | Molex 12 way Female Connector 1 Row | 1 | Element14 | Mouser | Attached with female crimp pins to harness | Twistyswrist Pins Seperately | |
| CrimpPin | Molex Crimp Terminal Suit Conn12Way | 11 | Element14 | Mouser | Female pins for neck 12 way board | ||
| Conn12WayM | Molex 12 way Male Connector 1 Row | 1 | Element 14 or here | Mouser | Soldered to Neck PCB | ||
| Conn6WayM | Molex 6 Way Male Connector 1 Row | 2 | Element 14 | 2 of these will fit perfectly if 12 way not available |
Custom Schematic Diagram for this Revision
